HolyBro SiK Telemetry Radio V3 100mW 433MHZ or 915Mhz


$79.99

Add to Cart:


  • Description
  • Details
  • Reviews
  • Custom Tab
Features
This Holybro SiK Telemetry Radio is a small, light and inexpensive open source radio platform
that typically allows ranges of better than 300m “out of the box” (the range can be
extended to several kilometres with the use of a patch antenna on the ground).
This radio is plug-n-play all Pixhawk Standard and other Flight Controller, providing the
easiest ways to setup a telemetry connection between your Autopilot and a ground station.
It uses open source firmware which has been specially designed to work well with MAVLink
packets and to be integrated with the Mission Planner, Ardupilot, QGroundControl, PX4 Autopilot.
The radios can be either 915Mhz or 433Mhz and you should purchase the model which is
appropriate for your country/region.
Note:
This radio does not support firmware upload via Mission Planner $95
1.3.75 or order. Please use
Mission Planner 1.3.75.1 or newer if firmware upload is needed.
- Open-source SIK firmware
- Plug-n-play for Pixhawk Standard Flight Controllers
- Easiest way to connect your Autopilot and Ground Station
- Interchangeable air and ground radio
- Micro-USB port (Type-C Adapter Cable Included)
- 6-position JST-GH connector
Product Details
- 100 mW maximum output power (adjustable) -117 dBm receive sensitivity
- RP-SMA connector
- 2-way full-duplex communication through adaptive TDM UART interface
- Transparent serial link
- MAVLink protocol framing
- Frequency Hopping Spread Spectrum (FHSS) Configurable duty cycle
- Error correction corrects up to 25% of bit errors Open-source SIK firmware
- Configurable through Mission Planner & APM Planner
- FT230X is a USB to BASIC UART IC
Dimensions
28 x 53 x 10.7mm (without antenna)
Electrical Data
- Supply voltage: 5V DC (from USB or JST-GH)
- Transmit current: 100 mA at 20dBm
- Receive current: 25 mA
- Serial interface: 3.3 V UART
HL-433MHZ
HolyBro SiK Telemetry Radio V3 100mW 433MHZ or 915Mhz for APM2.6 Pixhawk PX4 Controller
HolyBro SiK Telemetry Radio V3 100mW 433MHZ or 915Mhz for APM2.6 Pixhawk PX4 Controller
HolyBro SiK Telemetry Radio V3 100mW 433MHZ or 915Mhz for APM2.6 Pixhawk PX4 Controller
HolyBro SiK Telemetry Radio V3 100mW 433MHZ or 915Mhz for APM2.6 Pixhawk PX4 Controller
HolyBro SiK Telemetry Radio V3 100mW 433MHZ or 915Mhz for APM2.6 Pixhawk PX4 Controller
HolyBro SiK Telemetry Radio V3 100mW 433MHZ or 915Mhz for APM2.6 Pixhawk PX4 Controller
  • 100 Units in Stock

Be the first to write a review.  Write a Review.
Safety Tip


This product was added to our catalog on Friday 17 December, 2021.

Content

OFFTHEGRIDWATER.CA

Rc-toys Multi Rotor safty Tip Keep your PROPS OFF not installed until you are fully conversant/understand in full the functions of your Tx in full including TRAV (end Points), the arm and disarm procedures - realise that for a noob skiping or out-of-order set-up steps or moving sticks, or even static - PROPS may start at anytime without warning. Never install props prior to calibration of the ESC and testing the gyro orientation, and arm/disarm testing of the board - YOU are responsible - make sure your actions and your Copter is safe. Never ASSUME the props will not start - removing the props removes the risk.



your alt text here