Pixhawk 5XAutopilot Flight Controller PM02D Power Module M8N GPS


$360.00

Add to Cart:


  • Description
  • Details
  • Reviews
  • Custom Tab
Features
* Modular flight controller: separated IMU, FMU, and Base system connected by a
100-pin & a 50-pin Pixhawk® Autopilot Bus connector, designed for flexible and customizable systems
* Redundancy: 3x IMU sensors & 2x Barometer sensors on separate buses, allowing parallel
and continuous operation even in the event of a hardware failure
* Triple redundancy domains: Completely isolated sensor domains with separate buses
and separate power control
* Newly designed vibration isolation system to filter out high frequency vibration
and reduce noise to ensure accurate readings
* Ethernet interface for high-speed mission computer integration
* Automated sensor calibration eliminating varying signals and temperature
* IMUs are temperature-controlled by onboard heating resistors, allowing optimum working
temperature of IMUs
* Two smart batteries monitoring on SMBus
* Additional GPIO line and 5V for the external NFC reader
* Secure element for secure authentication of the drone (SE050)
Product Details
Technical specification
* FMU Processor: STM32F765
* 32 Bit Arm® Cortex®-M7, 216MHz, 2MB memory, 512KB RAM
* IO Processor: STM32F100
* 32 Bit Arm® Cortex®-M3, 24MHz, 8KB SRAM
* On-board sensors
* Accel/Gyro: ICM-20649
* Accel/Gyro: ICM-42688P
* Accel/Gyro: ICM-20602
* Mag: BMM150
* Barometer: 2x BMP388
Electrical data
* Voltage Ratings:
* Max input voltage: 6V
* USB Power Input: 4.75~5.25V
* Servo Rail Input: 0~36V
Mechanical data
* Dimensions
* Flight Controller Module: 38.8 x 31.8 x 14.6mm
* Standard Baseboard: 52.4 x 103.4 x 16.7mm
* Weight
* Flight Controller Module: 23g
* Standard Baseboard: 51g
Interfaces * 16- PWM servo outputs
* R/C input for Spektrum / DSM
* Dedicated R/C input for PPM and S.Bus input
* Dedicated analog / PWM RSSI input and S.Bus output
* 4 general purpose serial ports
* 3 with full flow control
* 1 with separate 1A current limit
* 1 with I2C and additional GPIO line for external NFC reader
* 2 GPS ports
* 1 full GPS plus Safety Switch Port
* 1 basic GPS port
* 1 I2C port
* 1 Ethernet port
* Transformerless Applications
* 100Mbps
* 1 SPI bus
* 2 chip select lines
* 2 data-ready lines
* 1 SPI SYNC line
* 1 SPI reset line
* 2 CAN Buses for CAN peripheral
* CAN Bus has individual silent controls or ESC RX-MUX control
* 2 Power input ports with SMBus
* 1 AD & IO port
* 2 additional analog input
* 1 PWM/Capture input
* 2 Dedicated debug and GPIO lines
HL-5X-M8N
Holybro Pixhawk 5X Autopilot Flight Controller With PM02D Power Module M8N GPS For Drone Airplane Quadcopter
Holybro Pixhawk 5X Autopilot Flight Controller With PM02D Power Module M8N GPS For Drone Airplane Quadcopter
Holybro Pixhawk 5X Autopilot Flight Controller With PM02D Power Module M8N GPS For Drone Airplane Quadcopter
Holybro Pixhawk 5X Autopilot Flight Controller With PM02D Power Module M8N GPS For Drone Airplane Quadcopter
Holybro Pixhawk 5X Autopilot Flight Controller With PM02D Power Module M8N GPS For Drone Airplane Quadcopter
Holybro Pixhawk 5X Autopilot Flight Controller With PM02D Power Module M8N GPS For Drone Airplane Quadcopter
  • 100 Units in Stock

Be the first to write a review.  Write a Review.
Safety Tip


This product was added to our catalog on Friday 17 December, 2021.

Content

OFFTHEGRIDWATER.CA

Rc-toys Multi Rotor safty Tip Keep your PROPS OFF not installed until you are fully conversant/understand in full the functions of your Tx in full including TRAV (end Points), the arm and disarm procedures - realise that for a noob skiping or out-of-order set-up steps or moving sticks, or even static - PROPS may start at anytime without warning. Never install props prior to calibration of the ESC and testing the gyro orientation, and arm/disarm testing of the board - YOU are responsible - make sure your actions and your Copter is safe. Never ASSUME the props will not start - removing the props removes the risk.



your alt text here