RMD-L-12025 BGC 3 MOTOR kit Support BaseCam Electronics control



$1,200.00

Add to Cart:


  • Description
  • Details
  • Reviews
  • Custom Tab
Features
3 RMD-L-12025 Motors + AC5000 1 main BaseCamElectronics control+2pcs driver+1 pc IMU+1 USB convert to serial interface
1.Mechatronics design with built in motor drive and position sensor.
2.Large diameter with more pole pairs design ,providing higher torque and smaller space application.
3.Abundant product models, diameter range:20mm-140mm;torque range:0.02-5N.M
4.Support RMD Assistant setting, and easy use
5.Wide voltage input range, support customize winding
6.Environmental condition of working from -40 to 80 Celsius
7.Support multiple communication methods RS485 or Can Bus.
8.Standard industry closed loop control mode(torque /speed/position) and support customize function
9.Support motor speed up to 4000RPM
10.Multiple protection functions, over temperature, over voltage and over current.
11.Apply for the filed which need precise control low speed and large torque such as
service robot, laser radar, gimbal and Laboratory test equipment
Product Details
Technical specifications
【Item Name】 RMD-L-12025
【Turns】 T 40
【Nominal Voltage】 V 24
【Nominal Current】 A 5.35
【Nominal Torque】 N.M 5.08
【Nominal Speed】 rpm 162
【Max Speed】 rpm 245
【Max Instant Torque】 N.M 7.7
【Max Instant Current】 A 8.1
【Line Resistance】 Ω 2.8
【Wire Connect】 Y
【Phase to Phase Inductance】 mH 5
【Speed Constant】 rpm/V 10
【Torque Constant】 N.M/A 0.95
【Rotor Inertia】 gcm^2 5500
【Number of Pole Pairs】 21
【Motor Weight】 g 1145
【Working Temperature】 °C -20°C~80°C
【Max Demagnetize Temperature】 °C 120°C
Matched Driver Matched Driver 【Drive】 DRC10
【Input Voltage】 V 8~36
【Current】 A Normal:8A Instant:15A
【Nominal Power】 W 200
【Communication】 RS-485/CAN BUS
【Encoder】 14-bit magnetic encoder
【Baud Rate】 9600、19200、57600、115200(default)
【Communication frequency】 RS485@115200BPS:500HZ; CAN BUS@1MBPS:2KHZ
【Communication frequency】 Torque open loop:24kHZ/Speed loop:8kHZ/Position loop:4KHZ
【Control frequency】 Torque open loop/speed loop/position loop
【S-Curve】 YES
【ID switch】 YES
【Connector】 ZH1.5/8PIN
【Temperature sensor】 YES
RMD-L-12025
RMD-L-12025 BGC MOTOR Support BaseCam Electronics control
RMD-L-12025 BGC MOTOR Support BaseCam Electronics control
RMD-L-12025 BGC MOTOR Support BaseCam Electronics control
  • 100 Units in Stock

Be the first to write a review.  Write a Review.
Safety Tip


This product was added to our catalog on Friday 03 June, 2022.

Content

OFFTHEGRIDWATER.CA

Rc-toys Multi Rotor safty Tip Keep your PROPS OFF not installed until you are fully conversant/understand in full the functions of your Tx in full including TRAV (end Points), the arm and disarm procedures - realise that for a noob skiping or out-of-order set-up steps or moving sticks, or even static - PROPS may start at anytime without warning. Never install props prior to calibration of the ESC and testing the gyro orientation, and arm/disarm testing of the board - YOU are responsible - make sure your actions and your Copter is safe. Never ASSUME the props will not start - removing the props removes the risk.



your alt text here