5.8GHz Diversity LCD Screen Receiver Monitor for FPV


Add to Cart:

  • Description
  • Details
  • Reviews
  • Custom Tab
☆ Built-in dual receiver automatically for best reception automatic antenna switching
☆ Dual buffered AV outputs
☆ Can receive 2 different channels at the same time
☆ AV receiver with diversity in puts
☆ Small,light weight,durable
☆ 4 Bands and total 32 Channels
☆ Built-in battery,easy to carry and outdoor use
☆ A key to automatic signal search,simple operation
☆ Work status OSD display: Always be aware of the device working condition

Product Details:

☆ Built-in 5.8Ghz Dual diversity receiver automatically for best reception
☆ Built-in 2CH 5.8Ghz AV output and 1CH AV input
☆ Built-in high performance Li-POLYMER Battery 1600mAH/7.4V
☆ Work status OSD display: RSSI indication; Battery indicator; Channel indication
☆ A key to automatic signal search
☆ Support Chinese and English menu
☆ Size: 180mm x 120mm x 50mm(Note: Sunshield height: 28mm)
☆ Working Voltage: DC 7-16V
☆ Power Consumption: max 650mA @ 12V
☆ Battery charging current : 850mA @ 12V ( max )
☆ Working temperature: - 10O C ~ +65O C
☆ Screen size: 7"
☆ Screen type: TFT LCD Screen/long life,LED backlight
☆ Resolution: 800x480
☆ Brightness: 450cd/m2
☆ View angle: 140/120 degree (Horizontal / Vertical)
Band and Channel selection
A5865 MHZ5845 MHZ5825 MHZ5805 MHZ5785 MHZ5765 MHZ5745 MHZ5725 MHZ
B5733 MHZ5752 MHZ5771 MHZ5790 MHZ5809 MHZ
5866 MHZ
E5705 MHZ5685 MHZ5665 MHZ5645 MHZ5885 MHZ5905 MHZ5925 MHZ5945 MHZ
Press this  button  to  enter the signal search, it will automatically  search  for  the  signals to a certain  signal  strength and  stops  on  that  channel , the  signal is not  found, will be on  the channel before starting the search  stopped; searching process, all the  buttons  will not operate ;
MENU pressed, this button  is used as number +.
DIVERSITY: true  diversity reception model,RF- A and RF- B the signal strength  of a display, to achieve the  best  radio  reception: corresponding to  the  RF- A and  RF- B indicator LED will flash alternately.
RF A:  RF A single received signal
RF B:  RF B single received signal
AV IN:  External input AV signal
MENU pressed,this button  is used as the value -
LCD display parameter adjustment, where the parameters using+,- to adjust, click MEUN,choose  a different adjustment items
4)  GROPU/↓
Default mode, click the GROUP option, a, b,e,f  cycle selection;
MENU pressed, this button  is used as Down ↓
Default mode, click the option  for the  CH 1-8 cycles;
MENU pressed, this button  is used as Up ↑
Press 0.5s boot, then press 0.5s shutdown.
1) RF A AV OUT: RF A receives the output of an AV signal,RF A mode must.
2) RF B AV OUT: RF B receives the output of a n AV signal ,RF B mode must.
3) DIVERSITY AV OUT: DIVERSITY the received AV signal output, DIVERSITY mode must
4) DC/+12V DC IN, +12V power supply , the device  operating current of 650mA @ 12V, built-in battery maximum charge current of 800mA @ 12V; if the device is working when charging , please pay attention to selecting the rated current greater than 2A/12V charging equipment.
3. Battery
Built-in 7.4V 1800mAH high-capacity polymer  battery, when the  battery is charging,the device where the lower left corner labeled cells , the red LED will light when charging is completed,here are bright green LED.
Note: If the device is not used for a long time , Please charged once every four months, in order to  protect the battery.
  • 99 Units in Stock

Be the first to write a review.  Write a Review.
Safety Tip

This product was added to our catalog on Wednesday 13 August, 2014.



Rc-toys Multi Rotor safty Tip Keep your PROPS OFF not installed until you are fully conversant/understand in full the functions of your Tx in full including TRAV (end Points), the arm and disarm procedures - realise that for a noob skiping or out-of-order set-up steps or moving sticks, or even static - PROPS may start at anytime without warning. Never install props prior to calibration of the ESC and testing the gyro orientation, and arm/disarm testing of the board - YOU are responsible - make sure your actions and your Copter is safe. Never ASSUME the props will not start - removing the props removes the risk.

your alt text here