Holybro PM03D Power Module I2C Power Monitor W/ XT-30 & XT-60


$56.00

Add to Cart:


  • Description
  • Details
  • Reviews
  • Custom Tab
Features
Overview
PM03D provides regulated power supply as well as current consumption and battery voltage
measurements via I2C digital protocol all through a 6pin 2.00mm CLIK-Mate cable.
Compatible to flight controller that uses I2C power monitor such as the Pixhawk 5X and up.
It is design for multi-rotor like the X500 V2. It has both XT-30 & XT-60 connectors
preinstalled for motor ESCs and Battery, as well as two 5V BEC and a
selectable 8V/12V output different kinds of peripheral devices.
Note: This PM is not compatible with flight controller that uses analog
PM such as the Pixhawk4, Pixhawk4 Mini, pix32 v5, or Durandal flight controllers.
• Plug & play, no additional setup required for QGround control & Mission Planner
• XT-30 connectors and solder pads for easy motor ESC connection
• Onboard voltage regulators: two 5.2V & one selectable 8V/12V
• 5V/A ports for powering companion computer or peripheral device
• Selectable 8V or 12V triple row pin header for powering peripheral device
Product Details
Maximum input voltage: 6S battery
Rated current: 60A
Max current: 120A (<60 Sec)
Max current sensing: 164A
Connections
XT-60 for battery
XT-30 for motor & peripheral device (battery voltage)
Solder pads in each corner (battery voltage)
CLIK-Mate 2.0mm for flight controller (5.2V/3A standalone BEC)
JST GH 4pin (5.2V/3A, BEC shared with 5.2V triple row pin header)
2x Triple row pin header (5.2V/3A, BEC shared with JST GH 4pin)
2x Triple row pin header (8V or 12V selectable by moving header jumper, 3A)
Dimension: 84*78*12mm (excluding wires)
Mounting: 45*45mm
Weight: 59g
The XT60 plug and 12AWG wire that PM03D comes with is rated for
30A continuous current and 60A instantaneous current (<1 minute).
If a higher current is being used, the plug type and wire
size should be changed accordingly.
HL-PM03D
Holybro PM03D Power Module Compatible to Flight Controller Uses I2C Power Monitor W/ XT-30 & XT-60 Connectors for Pixhawk 5X Flight Controll
Holybro PM03D Power Module Compatible to Flight Controller Uses I2C Power Monitor W/ XT-30 & XT-60 Connectors for Pixhawk 5X Flight Controll
Holybro PM03D Power Module Compatible to Flight Controller Uses I2C Power Monitor W/ XT-30 & XT-60 Connectors for Pixhawk 5X Flight Controll
Holybro PM03D Power Module Compatible to Flight Controller Uses I2C Power Monitor W/ XT-30 & XT-60 Connectors for Pixhawk 5X Flight Controll
Holybro PM03D Power Module Compatible to Flight Controller Uses I2C Power Monitor W/ XT-30 & XT-60 Connectors for Pixhawk 5X Flight Controll
  • 100 Units in Stock

Be the first to write a review.  Write a Review.
Safety Tip


This product was added to our catalog on Tuesday 28 June, 2022.

Content

OFFTHEGRIDWATER.CA

Rc-toys Multi Rotor safty Tip Keep your PROPS OFF not installed until you are fully conversant/understand in full the functions of your Tx in full including TRAV (end Points), the arm and disarm procedures - realise that for a noob skiping or out-of-order set-up steps or moving sticks, or even static - PROPS may start at anytime without warning. Never install props prior to calibration of the ESC and testing the gyro orientation, and arm/disarm testing of the board - YOU are responsible - make sure your actions and your Copter is safe. Never ASSUME the props will not start - removing the props removes the risk.



your alt text here