Matek FCHUB-W PDB 3-6S Built-in 4 BEC & 104A Current Sensor


$22.00

Add to Cart:


  • Description
  • Details
  • Reviews
  • Custom Tab
Features
Matek FCHUB-W PDB 3-6S Built-in 4 BEC & 104A Current Sensor for RC FPV Racing Drone Models Multicopter DIY Accessories
Product Details
Input voltage range: 9~30V (3~6S LiPo) w/TVS protection
Current Senor: 104A, 3.3V ADC, Scale 317
Mounting: 30.5 x 30.5mm, Φ3mm
Sizes: 52 x 36 x 6 mm
Weight: 13g
2x ESC power pads
4x BEC on board
3x LED indicators for 5V, 10V & Vx
Soldering Holes & Pads:
+ & – : Bettery & ESC power pads
Curr: Current sensor output
Vbat: Bettery voltage
G: Ground
3V3: LDO 3.3V
5V: BEC 5V
10V: BEC 10V
Vx: BEC 5V/6V/7.2V ADJ
FFlight Controller connection:
Compatible with MATEKSYS Flight Controller F405-STD, F722-STD, F405-OSD
MT1: Motor1 of INAV Flying Wing & Airplane
MT2: Motor2 of INAV Flying Wing & Airplane
SV3~SV6: Servo 3~6 of INAV Flying Wing & Airplane
VTX: Video Transmitter signal
TX5 & RX5: UART5 of F405-STD/F722-STD/F405-OSD
BEC 5V output:
Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, GPS module
DC/DC synchronous buck regulator
Voltage: 5.0 +/- 0.1VDC
Continuous current: 2 Amps, Max.3A
Output Ripple: 20mV (VIn=24V, VOut=5V@2A load)
Short-circuit tolerant (2 seconds)
BEC 10V output:
Designed for Video Transmitter, Gimble
DC/DC synchronous buck regulator
Voltage: 10.0 +/- 0.2VDC (Input voltage >11V)
Continuous current: 2 Amps, Max.3A
Output Ripple: 20mV (VIn=24V, VOut=10V@2A load)
Short-circuit tolerant (2 seconds)
BEC Vx output:
Designed for Servos
DC/DC synchronous buck regulator
Voltage adjustable, 5V Default, 6V or 7.2V via jumper
Continuous current: 5 Amps, Max.5.5A
Output Ripple: 50mV (VIn=24V, VOut=5V@5A load)
Short-circuit tolerant (2 seconds)
BEC 3.3V output
Designed for Baro / compasses module and spektru m RX
Linear Regulator
Continuous current: 500mA
Matek FCHUB-W PDB 3-6S Built-in 4 BEC & 104A Current Sensor
  • 100 Units in Stock

Be the first to write a review.  Write a Review.
Safety Tip


This product was added to our catalog on Wednesday 28 February, 2018.

Content

OFFTHEGRIDWATER.CA

Rc-toys Multi Rotor safty Tip Keep your PROPS OFF not installed until you are fully conversant/understand in full the functions of your Tx in full including TRAV (end Points), the arm and disarm procedures - realise that for a noob skiping or out-of-order set-up steps or moving sticks, or even static - PROPS may start at anytime without warning. Never install props prior to calibration of the ESC and testing the gyro orientation, and arm/disarm testing of the board - YOU are responsible - make sure your actions and your Copter is safe. Never ASSUME the props will not start - removing the props removes the risk.



your alt text here