R14FA CORONA 2.4Ghz 14CH Fasst Compatible Reciver


$33.99

Add to Cart:


  • Description
  • Details
  • Reviews
  • Custom Tab
Features
CORONA R14FA 2.4Ghz 14CH Fasst Compatible Reciver (Compatible with futaba Fasst 14SG 16SZ 18MZ HV )
Product Details
Compatibility:
FASST 2.4G Air Systems(7CH Mode/Multi Mode):6EX,7C,TM-7,TM-8,T8FG,T10C,
TM-10,T10CG,14SG,T12Z,T12FG,TM-14,T14MZ,etc.
FASST 2.4G Surface Systems(C1 Mode):3PK,4PK,etc
Specifications:
Operating Current:
70mA @ FASST 7ch mode normal and 110 mA max,
80mA @ FASST multi-channel mode normal and 110 mA max
Operating Voltage: 4.0 ~10V
Latency:
7mS for high speed PPM (HS), 14mS for low speed PPM (LS) @ FASST multi-channel mode,
8ms for high speed PPM (HS), 16mS for low speed PPM (LS) @ FASST 7ch mode
Sensitivity: about -96dBm
Setup:
Bind procedure:
Turn on the FASST transmitter
Connect the battery to the receiver while pressing receiver's F/S button.
The Dual-color LED's continuous will cycle through the following:
Red LED light (searching radio signal)
Green LED light (acquired the radio signal)
Red LED off (bind ok)
Green LED flashes 10 times (ID store in memory)
Green LED lights solid (normally operation)
Fail-safe setting:
There are two ways to set the Failsafe setting on the CORONA 2.4GHz Spread Spectrum FASST Compatible Receiver.
1.TX-failsafe Features: This method is to set failsafe on the FASST transmitter and has priority (works on channel 3 only under FASST 7ch mode or on multiple-channels under FASST multi-channel mode) while the receiver is working on, just like the FUTABA receivers.
2.RX-failsafe Features: Turn on FASST transmitter and turn on the CORONA 2.4GHz Spread Spectrum Receiver, put all the sticks and switches to where give the control inputs you want if the receiver looses signal and Press the F/S button down for about 5 - 6 seconds while the Green LED light solid (Rx in normal operation), then release the button. You will see the Red LED will flash for about 4 - 5 seconds. (Note: The Red LED will FLASH high speed to indicate the RX-failsafe is turned on OR FLASH low speed to indicate
Item Packing
R14FA receiver x 1
Detailed Images
R14FA CORONA 2.4Ghz 14CH Fasst Compatible Reciver (Compatible with futaba Fasst 14SG 16SZ 18MZ HV )
R14FA CORONA 2.4Ghz 14CH Fasst Compatible Reciver (Compatible with futaba Fasst 14SG 16SZ 18MZ HV )
  • 100 Units in Stock

Be the first to write a review.  Write a Review.
Safety Tip


This product was added to our catalog on Sunday 13 December, 2020.

Content

OFFTHEGRIDWATER.CA

Rc-toys Multi Rotor safty Tip Keep your PROPS OFF not installed until you are fully conversant/understand in full the functions of your Tx in full including TRAV (end Points), the arm and disarm procedures - realise that for a noob skiping or out-of-order set-up steps or moving sticks, or even static - PROPS may start at anytime without warning. Never install props prior to calibration of the ESC and testing the gyro orientation, and arm/disarm testing of the board - YOU are responsible - make sure your actions and your Copter is safe. Never ASSUME the props will not start - removing the props removes the risk.



your alt text here