T580


$480.00

 Sold Out 

  • Description
  • Details
  • Reviews
  • Custom Tab

Ready to Fly Kit no Camera Mount


     

Product Details

-FS-CT6B 2.4G 6CH radio control System ( TX + RX ) -channels: 6channels;
-model type: heli, airplane, glider;
-RF power: less than 20db;
-modulation: GFSK;
-code type: PPM/PCM;
-sensitivity:1024;
-low voltage warning: yes;
-DSC port: yes;
-charger port: yes;
-power:12VDC(1.5AAA*8);
-weight:680g;
-ANT length:26mm;
-size:190*80*240mm;
-Color: black;
-certificate: CE FCC;

 

Features

-Inertial-based(6DOF IMU) self-stabilization system. Good for AV/AP applications, but not suitable for acrobatics flights.
-4 channels Tx is enough. No more switches for the flight modes
-ARTF, no extra settings needed. Put on the props, the battery and the RX, then turn on the Tx to take off !
-AP/AV based
-Auto Barometer-based altitude hold if no throttle input changed in 2s..
-X and Corss flight modes available. Only Cross mode was available in the beginning. But new improvements for the X mode had been tested successfully.
-Optional single axis camera mount (pitch) with double axis self-stabilization (pitch and roll).
-Larger MTM distance(580mm),larger payload (<580g),and longer flight time(25 mins with 3S Battery). Special props offered by the manufacture.
Powerful
-Buzzer warning for low battery, and optional lights for night flight (The interfaces are available, but soldering should be done before coming out -of the factory according to the demands of the costomers. In order to avoid some trouble of making the hardware easy to be damaged).
-Other features considering to be supported in the future: Configuration Software available and Firmware upgradeable.
-This is the RTF ,Including the remote control, receiver and batteries

 

Item Packing

-Pre-installed aircraft main body, including brushless ESC, flight control panel, motor X 1
-pre-installed stands unit, including 4 fixed nuts X1
-pairs of special propellers in positive and negative X 3
- bullet blade folders X 4
-Velcro X 1
-FS-CT6B 2.4G 6CH Transmitter&Receiver x 1
-Kypom 11.1v 2200mah 30c Battery x 1                                                                                                                                                                                                                                                                                                                               

-Battery Lipo Charger  X1

Product Details

Machine size
 

608 × 608 × 243

mm

±3mm

Expand size of the largest
 

885 × 885 × 243

mm

 

Motor Wheelbase
t

Diagonal line, the two motor centers wheelbase

580mm

±3mm

Propeller
 

1260, positive and negative special paddle

12”

 

Battery
 

LiPo 3S 2200mAh 20C

1P

 

Single Weight
 

No battery, receiver, load

730g

±10g

Take-off weigh

3S 2200mAh 1P Battery, receiver, head

950g

standard

Payload
 

Camera card

≤230g

standard

Maximum power pulled
 

Using the standard battery 1P

2400g

 

-

Maximum payload
 

Using the standard battery 1P

≤580g

 

-

Maximum takeoff weight
 

Using the standard battery 1P

1800g

Safety limit

Flight distance
 

Remote control device and battery capacity by the decision

Line of sight

 

-

Flight Time
 

3S 2200mAh 1P Battery, receiver

12 minutes

No wind hover

Wind strength

≤4

Class

 

-

 

  • 0 Units in Stock
  • Manufactured by: Lotus RC

Be the first to write a review.  Write a Review.
Safety Tip


This product was added to our catalog on Sunday 19 February, 2012.

Content

OFFTHEGRIDWATER.CA

Rc-toys Multi Rotor safty Tip Keep your PROPS OFF not installed until you are fully conversant/understand in full the functions of your Tx in full including TRAV (end Points), the arm and disarm procedures - realise that for a noob skiping or out-of-order set-up steps or moving sticks, or even static - PROPS may start at anytime without warning. Never install props prior to calibration of the ESC and testing the gyro orientation, and arm/disarm testing of the board - YOU are responsible - make sure your actions and your Copter is safe. Never ASSUME the props will not start - removing the props removes the risk.



your alt text here