ELRS PP 2.4GHz PP RX Receiver SX1280 EXPRESSLRS Nano Long Range

(image for) ELRS PP 2.4GHz PP RX Receiver SX1280 EXPRESSLRS Nano Long Range
ELRS PP 2.4GHz PP RX Receiver SX1280 EXPRESSLRS Nano Long Range
  • 100 Units in Stock

 Ask a Question 

$25.99

Add to Cart:
Features
Since the Official Perfect version of ELRS firmware has not been released yet,
currently our PP_RX, EP1/EP2 RX and ES24TX pre-loaded firmware are all beta versions,
you can upgrade the official firmware when Official perfect target available.
More details: https://github.com/ExpressLRS/ExpressLRS
The Happymodel 2.4GHz ELRS nano series receiver is an open source program
based on ExpressLRS, we have 3 types rx module released.
The PP RX is designed by @Jye Smith from ExpressLRS development team.
Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip.
It has a built-in ceramic antenna, which is super light and small in size.
On the basis of PP RX, we have developed the Nano 2.4GHz rx of ESP8285 version
named EP1 and EP2. The RF module of EP1/EP2 is the same like PP RX and use
ESP8285 MCU . So you can upgrade firmware by WIFI , that's too simple.
Due to the low-latency and high-refresh-rate RF module, they are very comfortable
for FPV race and Long Range FPV. And very suitable for Tiny whoop because
of the ultra light and Nano size.
Product Details
Type: ISM
STM32L432KBU6 MCU
SX1280IMLTRT RF Module
SMD Ceramic antenna
Frequency Range: 2400 MHz to 2500 MHz
Maximum receive refresh rate: 500Hz
Minimum receiver refresh rate: 25Hz
Working voltage: 5v
Weight: 0.47gram
Dimension: 10mm*10mm*6mm
Peak gain: 3.7dB
Bind procedure:
1.Supply power to the PP/EP1/EP2 rx, wait until the LED on the RX is off,
immediately turn off the power, and then repeat again the above steps.
When the RX is powered on for the third time, the LED light will start to
double-flash, which means that the RX enters the binding mode
2.Insert the ES24TX module or other DIY 2.4G ELRS TX to Radio transmitter,
and choose External RF mode to CRSF protocol, then you can find ELRS menu
from the Radio systems(Need to copy the ELRS.LUA file to the SD-Card tools first),
Enter into ELRS and press [Bind], the LED on the RX module will getting
to be solid if bind successfully.
3.Receiver LED status meanings:
PP RX: LED solid means bind successful or Connection established; LED double-flash
means in bind mode; LED flash slowly means no signal connection from the TX module
EP1/EP2 RX: LED solid means bind successful or Connection established; LED double-flash
means in bind mode; LED flash slowly means no signal connection from the TX module;
LED flash fast means in WIFI hotspot mode, you can connect the WIFI of the
RX and upgrade firmware of the RX via visit 10.0.0.1(password:expresslrs)

ELRS PP 2.4GHz PP RX Receiver SX1280 EXPRESSLRS Nano Long Range Receiver For RC FPV Tinywhoop
ELRS PP 2.4GHz PP RX Receiver SX1280 EXPRESSLRS Nano Long Range Receiver For RC FPV Tinywhoop
ELRS PP 2.4GHz PP RX Receiver SX1280 EXPRESSLRS Nano Long Range Receiver For RC FPV Tinywhoop
ELRS PP 2.4GHz PP RX Receiver SX1280 EXPRESSLRS Nano Long Range Receiver For RC FPV Tinywhoop

Product 84/287

 Previous 
 Return to the Product List 
 Next 

This product was added to our catalog on Wednesday 14 April, 2021.

Copyright © 2024 OFF THE GRID WATER. Powered by Zen Cart