10x JR X2720 7CH Remote controller transmitter RC


$169.00

 Sold Out 

  • Description
  • Details
  • Reviews
  • Custom Tab

JR X2720 7CH Remote controller transmitter RC system 2.4GHz or model helicopter aircraft plane hobby

   
   
   
   
   

 

 

Product Details

Transmitter Specifications:

  • Multifunction 7 channel radio
  • User-friendly graphic display computer system
  • Comfortable fitted computer-designed, ergonomically styled transmitter case.
  • Advanced digital trim
  • Adjustable spring tensions and length by the ultra precision control sticks
  • Full PLL Synthesiser transmitter software (crystal free)
  • Fail safe function with SPCM modulation
  • Trainer function as standard equipment
  • Charging battery jack is fitted as a standard equipment
  • SPCM and PPM (FM) are available
  • Model name, data copy function
  • Same switch layout for heli and aero type
  • 20 model memory
  • 9.6V 1500mAh rechargeable battery included

Receiver Specifications:

  • Model Number: RS77S SPCM
  • Small and slimline design 7 channel receiver
  • FM-NEW ABC & W system makes R770 high sensitive.
  • A narrow band ceramic filter for high-signal selectivity assists in rejecting cross modulations from other common radio frequencies, such as RC transmitters for local paging systems.
  • S type PCM receiver developed by advanced digital technique using a high-reliability and super small micro computer
  • Fail safe function is operable.
  • Direct servo control for control servos without radio frequency output.

Servos:

  • Type: 591
  • Torque:5kg.cm
  • Speed:0.21 sec
  • Weight: 4 gm
  • Size mm (LxWxH): 18.6 x 35.0 x 38.3
    Ball bearing: Yes
  • Motor: Ferrite
  • Gears: Resin Carbonite

Charger:

  • Input Voltage: AC-240V
  • Output Current: 50mA TX/100 mA RX
  • Charging Time: 15-20 Hours

 

In the Box

-Transmitter incl 9.6V 1500mAh battery X 1
-RS77S Auto-scan PLL-Synthesized 7 channel SPCM receiver X 1
-591 servos w/ hardware X 1
-4N1100 Ni-Cd 4.8V/1100mah battery X 1
-RX & TX battery charger NEC-322 AC240V X 1
-switch harness X 1
-Manual ( ENGLISH version ) X 1

Features

JR X-2720 Key Features:

  • Fully synthesised and crystal-free
  • No frequency dials to turn
  • Improved programming with more mixes
  • IMproved interface
  • Based on proven 3810 package
  • 20-model memory
  • RS77S receiver & 591 servos included

JR X-2720 Programming Features:

System Mode:

  • Model Select
  • Model Name
  • Model type Select
  • Modulation Select
  • Model reset
  • Trainer system select
  • Throttle Recovery
  • Input Select (Switch Select-ability for Aux 2 and Gear)
  • Wing type
  • Swashplate type
  • Frequency Selection (Ch 601 - 659)
  • Dual Rate Switch Select

Airplane Function Mode:

  • Dual Rates
  • Exponential
  • Servo Reverse
  • Sub trim
  • Travel Adjust
  • Elevator to Flap Mix
  • Aileron To Rudder Mix
  • Flap System
  • Differential
  • Programmable Mix (1-6)
  • Fail Safe
  • Servo monitor

Helicopter Function Mode:

  • Dual Rates
  • Exponential
  • Servo Reverse
  • Sub trim
  • Travel Adjust
  • Swashplate Mix
  • Throttle Hold
  • Throttle Curve (3) (5 pt mix)
  • Pitch Curve (4) (5 pt mix)
  • Revolution Mix
  • Gyro Sensing
  • Fail Safe
  • Servo monitor

 

  • 0 Units in Stock
  • Manufactured by: JR

Be the first to write a review.  Write a Review.
Safety Tip


This product was added to our catalog on Thursday 01 March, 2012.

Content

OFFTHEGRIDWATER.CA

Rc-toys Multi Rotor safty Tip Keep your PROPS OFF not installed until you are fully conversant/understand in full the functions of your Tx in full including TRAV (end Points), the arm and disarm procedures - realise that for a noob skiping or out-of-order set-up steps or moving sticks, or even static - PROPS may start at anytime without warning. Never install props prior to calibration of the ESC and testing the gyro orientation, and arm/disarm testing of the board - YOU are responsible - make sure your actions and your Copter is safe. Never ASSUME the props will not start - removing the props removes the risk.



your alt text here