F405V3 50A Stack FC ECS BMI270 Flight Controller combo SpeedyBee

(image for) F405V3 50A Stack FC ECS BMI270 Flight Controller combo SpeedyBee
F405V3 50A Stack FC ECS BMI270 Flight Controller combo SpeedyBee
  • 100 Units in Stock

 Ask a Question 

$85.00

Add to Cart:
Features
Powerful Real 50A 4-in-1 ESC!
Built with the robust BB21 MCU and large motor pads for easy soldering.
Built with Japan made TDK filtering SMT capacitors + onboard
TVS protective diode, brings smooth flight experience.
Real 50A output, ready for your baddest 6S motors
Built with a 4-level LED battery indicator, now you
can fly anywhere worry-free - even without your lipo checker!
You could use this stack to build your X8 drones, Y6 drones
or fixed wings. Forget about crawling through your massive
build just to plug in that USB cable. Just take out your
phone to configure everything in the SpeedyBee app.
Product Details
* Product Name: SpeedyBee F405 V3 30x30 Flight Controller
* MCU: STM32F405
* IMU(Gyro): BMI270
* USB Port Type: Type-C
* Barometer: Built-in
* OSD Chip: AT7456E chip
* BLE Bluetooth: Supported. Used for Flight Controller configuration
(MSP should be enabled with Baud rate 115200 on UART4)
DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct soldering.
* 6-pin DJI Air Unit Plug: Supported. Completely compatible with DJI
O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
* Blackbox MicroSD Card Slot: *Betaflight firmware requires the
type of the microSD card to be either Standard (SDSC) or High
capacity (SDHC), so extended capacity cards (SDXC) are not supported
(Many high-speed U3 cards are SDXC). Also the card MUST be formatted
with the FAT16 or FAT32 (recommended) filesystems. So, you could use
any SD card less than 32GB, but the Betaflight can only recognize 4GB
maximum. We suggest you use this 3rd party formatting tool and choose
'Overwrite format' then format your card. Also check out here for the
recommended SD cards or buy the tested cards from our store.
* BetaFlight Camera Control Pad: Yes(CC pad on the front side)
* Current Sensor Input: Supported. For SpeedyBee BLS 50A ESC,
please set scale = 386 and Offset = 0.
* Power Input: 3S - 6S Lipo(Through G, BAT pins/pads from the
8-pin connector or 8-pads on the bottom side)
* 5V Output: 9 groups of 5V output, four +5V pads and 1 BZ+ pad
( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 2A.
* 9V Output: 2 groups of 9V output, one +9V pad on front side and
other included in a connector on bottom side. The total current load is 2A.
* 3.3V Output: Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
* 4.5V Output: Supported. Designed for receiver and GPS module
even when the FC is powered through the USB port. Up to 1A current load.
* ESC Signal: M1 - M4 on bottom side and M5-M8 on front side.
* UART: 6 sets(UART1, UART2, UART3, UART4(Dedicated for
Bluetooth connection), UART5(Dedicated for ESC telemetry),UART6
ESC Telemetry: UART R5(UART5)
* I2C: Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
* Traditional Betaflight LED Pad: Supported. 5V, G and LED
pads on bottom of the front side. Used for WS2812 LED
controlled by Betaflight firmware.
* Buzzer: BZ+ and BZ- pad used for 5V Buzzer
* BOOT Button: Supported.
[A]. Press and hold BOOT button and power the FC on at the same
time will force the FC to enter DFU mode, this is for
firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT
button can be used to controller the LED strips connected to
LED1-LED4 connectors on the bottom side. By default, short-press
the BOOT button to cycle the LED displaying mode. Long-press the
BOOT button to switch between SpeedyBee-LED mode and BF-LED mode.
Under BF-LED mode, all the LED1-LED4 strips will be controlled
by Betaflight firmware.
* RSSI Input: Supported. Named as RS on the front side.
* Smart Port / F.Port: Not supported
* Supported Flight Controller Firmware: BetaFlight(Default), EMUFlight, INAV
* Firmware Target Name: SPEEDYBEEF405V3
* Mounting: 30.5 x 30.5mm( 4mm hole diameter)
* Dimension: 41.6(L) x 39.4(W) x 7.8(H)mm
* Weight: 9.6g
* Product Name:SpeedyBee BLS 50A 30x30 4-in-1 ESC
* Firmware:BLHeli_S JH50
* Wireless Configuration:Full Configuration Supported in the SpeedyBee app
* PC Configurator Download Link:https://esc-configurator.com/
* Continuous Current:50A * 4
* Burst Current:55A(5seconds)
* TVS Protective diode:Yes
* External Capacitor:1000uF Low ESR Capacitor(In the package)
* ESC Protocol:DSHOT300/600
* Power Input:3-6S LiPo
* Power Output:VBAT
* Current Sensor:Support (Scale=386 Offset=0)
* ESC Telemetry:Not supported
* Mounting:30.5 x 30.5mm( 4mm hole diameter)
* Dimension:45.6(L) * 44(W) * 6.1mm(H)
* Weight:13.8g
F405-V3-50A
SpeedyBee F405 V3 50A Stack FC ECS BMI270 30x30 Flight Controller BLS 50A 4-in-1 ESC 3-6S LiPo For RC FPV Drone
SpeedyBee F405 V3 50A Stack FC ECS BMI270 30x30 Flight Controller BLS 50A 4-in-1 ESC 3-6S LiPo For RC FPV Drone
SpeedyBee F405 V3 50A Stack FC ECS BMI270 30x30 Flight Controller BLS 50A 4-in-1 ESC 3-6S LiPo For RC FPV Drone
SpeedyBee F405 V3 50A Stack FC ECS BMI270 30x30 Flight Controller BLS 50A 4-in-1 ESC 3-6S LiPo For RC FPV Drone
SpeedyBee F405 V3 50A Stack FC ECS BMI270 30x30 Flight Controller BLS 50A 4-in-1 ESC 3-6S LiPo For RC FPV Drone
SpeedyBee F405 V3 50A Stack FC ECS BMI270 30x30 Flight Controller BLS 50A 4-in-1 ESC 3-6S LiPo For RC FPV Drone

Product 65/230

 Previous 
 Return to the Product List 
 Next 

This product was added to our catalog on Wednesday 29 March, 2023.

Copyright © 2024 OFF THE GRID WATER. Powered by Zen Cart