CUAV NEO 3 PRO GNSS U-BLOX M9N GPS Module


$189.99

Add to Cart:


  • Description
  • Details
  • Reviews
  • Custom Tab
Features
NEO 3 Pro adopts SAW+LNA+SAW triple filter design, effectively avoiding the influence of
remote control, data transmission, 4G signal on GPS positioning reception
New generation satellite receiver Ublox M9N,The actual measurement can reach a maximum accuracy of 0.7m.
Supports simultaneous reception of Beidou, Galileo, Glonas, and GPS four satellite systems
Product Details
Processor:STM32F412
Compass:RM3100
Barometer:MS5611
GNSS receiver:UBLOX NEO M9N
RGB drive:NCP5623C
Buzzer:Passive buzzer
Safety switch:Physical button
GNSS:Beidou、Galileo、 GLONASS、 GPS
GNSS Augmentation System
-SBAS:WAAS,EGNOS,MSAS
-QZSS:L1s(SAIF)
-other:RTCM3.3
Number of concurrent GNSS:4
Frequency band
-GPS:L1C/A
-GLONASS:L10F
-Beidou:B1I
-Galileo:E1B/C
Horizontal accuracy:2.0M
Speed accuracy:0.05M/S
Nav. update rate:25Hz(Max)
Acquisition
-Cold start:24S
-Hot start:2S
-Aided start:2s
Number of satellites(MAX):32+
Sensitivity
-Tracking and nav-167dBm
-Cold start Hot star-148dBm
-Reacquisition -160dBm
Protocol:UAVCAN
Port TYpe:GHR-04V-S
Supported flight controller:CUAV series,
Pixahwk series
Wave filtering:SAW+LNA+SAW
Anti-Electromagnetic/radio frequency interference:EMI+RFI
Upgrade firmware:support Support Flight control type:Ardupilot/PX4*(PX4 is still working hard to adapt to the clock)
Input voltage:5V
Operating temperature:-10~70℃
Size:60*60*16MM
Weight:33g

CUAV NEO 3 PRO GNSS U-BLOX M9N GPS Module For PIX Flight Controller Pixhawk with Ardupilot PX4 Open Source 4 Starts
CUAV NEO 3 PRO GNSS U-BLOX M9N GPS Module For PIX Flight Controller Pixhawk with Ardupilot PX4 Open Source 4 Starts
CUAV NEO 3 PRO GNSS U-BLOX M9N GPS Module For PIX Flight Controller Pixhawk with Ardupilot PX4 Open Source 4 Starts
CUAV NEO 3 PRO GNSS U-BLOX M9N GPS Module For PIX Flight Controller Pixhawk with Ardupilot PX4 Open Source 4 Starts
CUAV NEO 3 PRO GNSS U-BLOX M9N GPS Module For PIX Flight Controller Pixhawk with Ardupilot PX4 Open Source 4 Starts
  • 100 Units in Stock

Be the first to write a review.  Write a Review.
Safety Tip


This product was added to our catalog on Wednesday 05 May, 2021.

Content

OFFTHEGRIDWATER.CA

Rc-toys Multi Rotor safty Tip Keep your PROPS OFF not installed until you are fully conversant/understand in full the functions of your Tx in full including TRAV (end Points), the arm and disarm procedures - realise that for a noob skiping or out-of-order set-up steps or moving sticks, or even static - PROPS may start at anytime without warning. Never install props prior to calibration of the ESC and testing the gyro orientation, and arm/disarm testing of the board - YOU are responsible - make sure your actions and your Copter is safe. Never ASSUME the props will not start - removing the props removes the risk.



your alt text here