Pixracer Autopilot Xracer V1.0 Flight Controller Mini PX4 Wifi


 Sold Out 

  • Description
  • Details
  • Reviews
  • Custom Tab
with M8N GPS For FPV Racing RC Multirotor Pixracer Autopilot Xracer V1.0 Flight Controller Mini PX4 Built-in Wifi and MINI M8N GPS For FPV Racing RC Multirotor Part No.:
The new Pixracer (formerly called XRacer) is available now and its fully supported by the Arducopter and PX4 community. Its a genuine open source project, already running with PX 4 stack software / QGroundControl (QGC), as well with Arducopter / Mission Planner (MP).
This is not just another small Pixhawk knock off or derivate, the Pixracer is the first autopilot of the new FMUv4 Pixhawk generation. Its coming with an upgraded Invensense Sensor generation (bye bye tricky LSM 303), a plug in Wifi board and last not least with a 2MB Flash : A real upgrade compared to former versions.
Mini NEO-M8N flight control source GPS choice matching with its high precision positioning accuracy and fast search efficiency will star. The store introduced the GPS NEO-M8N imported M8N chip, and the functional module group to optimize the built-in electronic compass, refresh rate increased to 10HZ. The accuracy of a higher search speed and a significant increase in the number of support for Europe's Galileo, Russia's GLONASS, Japan's little sun, China's big dipper. Module supports GPS+ compass +SBAS or GPS+GLONASS+SBAS. Product Details
Item name: Pixracer V1.0 Flight
MCU: STM32F427VIT6 rev.3
PCB dimension: 36mm*36mm
LDO Ultra low noise LDOs for sensors and FMU
MPU9250, ICM20608, baro MS5611, mag HMC5983
Connectors: GPS+I2C, RC-IN, PPM-IN, RSSI, SBus-IN, Spektrum-IN, USART3 ( TxD, RxD, CTS, RTS ), USART2 ( TxD, RxD, CTS, RTS ), FRSky-IN, FRSky-OUT, CAN, USART8 ( TxD, RxD ), ESP8266 ( full set ), SERVO1-SERVO6, USART7 ( TxD, RxD ), JTAG ( SWDIO, SWCLK ), POWER-BRICK ( VDD, Voltage, Current, GND ), BUZZER-LED_BUTTON
MicroSD card reader
Micro USB
WiFi ESP8266 802.11bgn ( Included !) .
This popular add on is a very versatile solution, you might want to check its wiki as well: http://www.esp8266.com/wiki/doku.php...th-the-esp8266 But don´t be scared, the included WiFi Module is coming ready to go ! JST GH series connectors for easy and robust peripheral connections, DF13 haters will love those!
Dimensions: 36 x 36mm with 30.5 x 30.5mm hole grid with 3.2mm holes Weight Pixracer: ( incl uSD and WiFi ) - app. 10.9g , ACSP4 - 7.86g ACSP5 app. 2.32g
Full set of professional flexible silicone cables for almost any peripheral module included. Power supply - 5-5.5VDC from USB or PowerBrick connector.
Item Packing
1 x Pixracer V1.0 Flight Controller
1x Mini M8N GPS

  • 0 Units in Stock

Be the first to write a review.  Write a Review.
Safety Tip

This product was added to our catalog on Friday 27 May, 2016.



Rc-toys Multi Rotor safty Tip Keep your PROPS OFF not installed until you are fully conversant/understand in full the functions of your Tx in full including TRAV (end Points), the arm and disarm procedures - realise that for a noob skiping or out-of-order set-up steps or moving sticks, or even static - PROPS may start at anytime without warning. Never install props prior to calibration of the ESC and testing the gyro orientation, and arm/disarm testing of the board - YOU are responsible - make sure your actions and your Copter is safe. Never ASSUME the props will not start - removing the props removes the risk.

your alt text here